![]() I'm going to have to pay better attention as to which ones. What finally did, was ending a few of the groups processes within the process monitor. At first I thought maybe it was wsearch going bonkers, but shutting that down, had no positive impact. ![]() But I did note it was indexing the directory structure of my harddrive. Sadly, I'm not sure Windows gives each sub item in the group its own process ID. After seeing it in the task manager, I quickly jumped into process monitor to see why the network restricted group was running the HDD so hard. System has been up for awhile now (~5 hours). Quite a lot of reports of poor throughput, but I haven't seen anything like what I am encountering.įinally an recent thread about this issue. The only thing I can guess is that this Marvel 9128 Sata Controller is a piece of crap. I checked System Restore to see if there was a new restore point that was just created, and if it was the cause of the 100% disk access, but there was no new restore point. After 15 minutes the 100% access (but low throughput) stopped and Windows began downloading update KB3194496. I checked Windows Update and it showed "Downloading updates 10%" and that did not change, nor was there any network activity. ![]() I seen a lot of System Volume Information access along with Master File Table. Today I booted and the 100% access began. User Benchmark reports the average of all user's benchmark of this drive as: But even though read and write speed is low, performance is poor if I attempt to run other programs. On average the read and write speeds are less than 1 MB. What is strange is that it's 100% access, but the actual data transfer really low. It goes on for a long time, and system performance is poor. That's when it occurs for a period longer than 5 minutes. Right now, my biggest issue with this 100% hard disk activity seems to be when Windows is actually updating. I found it in the task scheduler but there are no triggers listed. ![]() I did some Googling and the only other thing I could come up with is that System Restore is creating a restore point after every boot. SFC never found any errors, but CHK DSK did. I have ESET NOD 32 AV installed, and I have run a complete scan with no hits. That doesn't explain the high disk access after every boot from 9/2 to 9/12. Every day? What in the world gives? Ok, perhaps there is an update getting pushed everyday so that is why I am seeing it so often. So, ok it seems it's getting ready to update Windows and is creating a System Restore point. The specific folders with the highest access as shown by Resource Monitor are System Volume Information and Software Distribution/Download. I'm not sure how long this has gone on, but I started noticing it about a month ago. Then find the Windows Update and double click it.Ĭhoose Disable under Startup Type then click OK.I am having typically 96-100% disk usage of my Windows 10 SSHD drive after every boot for approximately 10-15 minutes-sometimes longer. If you don’t want your unit to automatically run the update, please press ‘Win’+’R’ then input services.msc This will make HDD usage at 100% for about 5 minutes. HDD usage at 100% always occurs after the unit connects to a network and in this time Windows 10 will automatically run the Windows Update. *The following solution is not recommended as your notebook would be in an unsafe state. After you complete all these changes, please restart your device. If your device preinstalls McAfee, please right click McAfee icon (at the right bottom corner) then click Check for Updatesĥ. If not on version 1703 (or above), please enter All settings > Update & security to run Windows Update and update to version 1703 (or above), then restart your device after the update is finished.Ĥ. Please open All settings > System > About > to confirm your Windows 10 version is 1703 (or above). Please confirm your OS is Windows 10. HDD is mechanical hard disk and HDD 100% usage maintains for about 10 minutes (Open Task Manager > Click to check the status of Disk usage).Ģ. Please plug in the adapter and connect your device to the Internet, then open Control Panel > Power Option > Choose when to turn off the display > Under Power Plan Settings, set Put the computer to sleep to Neverģ. (Note: Please do NOT run any other programs while running the manual updates)ġ. Windows 10 and pre-installed McAfee will automatically update which will cause HDD usage to show 100% so please manually execute Windows Update and McAfee update and follow the instructions below: Windows Update and McAfee Update cause HDD usage reach 100% in Windows 10
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |